How do you remove and install Brake Calipers?

To remove the front brakes, start by loosening the lug nuts on the front wheels, but don't remove them completely. Then, raise the front of your ride and secure it on jackstands. Remove the front wheels and wash the brake assembly with brake system cleaner. Disconnect the brake line from the caliper and plug it to avoid contaminants entering the brake system hence minimizing loss of brake fluid. Next, remove the caliper mounting bolts and detach the caliper from its mounting bracket. To install new brakes on your vehicle's front, reverse removal of all components taken out ensuring that you replace sealing washers placed either side of a new fitting of a break line as well. Tighten banjo bolt along with caliper mounting bolts as per torque specifications.Thereafter,you will need to bleed your automotive braking system,mounting back tires together with lug nuts then lower down your car .Fasten lug nuts in compliance with their set torque specification while at this juncture.lowering is performed after installing wheel lugs while tightening them up properly.If you are considering rear brakes, follow a similar process.Firstly,don't forget to loosen up lug nuts on back wheels,later raise down rear side of your automobile which is then secured using jack stands.Remove rear wheels without forgetting to disengage parking brakes.dissemble brake lever by disconnecting parking cable then release it from bracket provided inside calliper.Unscrew banjo bolt then unplug fitting located at end point in order to prevent leakage because this may lead to contamination.Finally,take away caliper's mounting bolt sliding it off upper guide pin.To install new brakes you should adhere to an installation process that is opposite to removing so that sealing washer for threaded junction between line and clamp is tightened.Banjo bolt as well as caliper functional components must be fastened firmly when compared to other parts such as those in pistons.Carry out bleeding process across entire system where afterward wheels are installed on rims and lug nuts fastened before vehicle is allowed to descend as you tighten its lugs accordingly.The above procedures must be replicated while attending to the rear brakes.

Genuine Cadillac Deville Brake Calipers

Caliper

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

31 Brake Calipers found

View related parts
Cadillac Deville Caliper,Front Brake
Part Number: 18046193
$88.98 MSRP: $260.40
You Save: $171.42 (66%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: CALIPER, Wheel Brake Cylinder/Caliper; Caliper
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998-2002 Cadillac Deville | SEVILLE, SLS, STS | 8 Cyl 4.6L
View related parts
Cadillac Deville Caliper Kit,Rear Brake
Part Number: 18048081
$40.51 MSRP: $80.36
You Save: $39.85 (50%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: CALIPER KIT, Wheel Brake Cylinder/Caliper; Overhaul Kit
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2003-2005 Cadillac Deville | DEVILLE | 8 Cyl 4.6L
View related parts
Cadillac Deville Caliper Assembly, Front Brk (W/O Brk Pads & Brkt
Part Number: 84394384
$100.12 MSRP: $198.64
You Save: $98.52 (50%)
ADD TO CART
Product Specifications
- Other Name: Caliper
- Position: Front
- Replaced by: 87859910
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Cadillac Deville | DEVILLE | 8 Cyl 4.6L
View related parts
Cadillac Deville Caliper Asm,Front Brake (Service)
Part Number: 18046196
$143.26 MSRP: $284.26
You Save: $141.00 (50%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: CALIPER, Wheel Brake Cylinder/Caliper; Caliper
- Position: Front
- Replaces: 18029818
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-2005 Cadillac Deville | 4 DOOR, DEVILLE, FUNERAL COACH, HIGH LUXURY, LIMOUSINE, SEVILLE, STS, TOURING 4 DOOR, TOURING SEDAN | 8 Cyl 4.6L
View related parts
Cadillac Deville CALIPER ASM-FRT BRK (W/O BRK PADS & BRKT)
Part Number: 84803425
$121.55 MSRP: $239.49
You Save: $117.94 (50%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper
- Replaced by: 87859911
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Cadillac Deville | DEVILLE | 8 Cyl 4.6L
View related parts
Cadillac Deville Caliper Asm,Front Brake (W/O Brake Pads) (Remanufacture)
Part Number: 19141029
$46.59 MSRP: $85.35
You Save: $38.76 (46%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: CALIPER, Wheel Brake Cylinder/Caliper; Caliper
- Position: Front
- Replaces: 18036713, 18021841, 18060191, 18017232
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1985-1990 Cadillac Deville | 2 DOOR, 4 DOOR, 60 SPECIAL 4 DOOR, BROUGHAM 2 DOOR FWD, BROUGHAM 4 DOOR FWD, CONVERSION, FUNERAL COACH, LIMOUSINE 4 DOOR, LIMOUSINE 4 DOOR CTR PART | 6 Cyl 4.3L Diesel, 8 Cyl 4.1L, 8 Cyl 4.5L
View related parts
Cadillac Deville Caliper Asm,Front Brake (W/O Brake Pads) (Remanufacture)
Part Number: 19141028
$46.59 MSRP: $85.35
You Save: $38.76 (46%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: CALIPER, Wheel Brake Cylinder/Caliper; Caliper
- Position: Front
- Replaces: 18017231, 18060190, 18036714
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1985-1990 Cadillac Deville | 2 DOOR, 4 DOOR, 60 SPECIAL 4 DOOR, BROUGHAM 2 DOOR FWD, BROUGHAM 4 DOOR FWD, CONVERSION, FUNERAL COACH, LIMOUSINE 4 DOOR, LIMOUSINE 4 DOOR CTR PART | 6 Cyl 4.3L Diesel, 8 Cyl 4.1L, 8 Cyl 4.5L
View related parts
Cadillac Deville Caliper Kit,Rear Brake
Part Number: 18042415
$24.38 MSRP: $63.64
You Save: $39.26 (62%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: CALIPER KIT, Wheel Brake Cylinder/Caliper; Caliper Overhaul Kit, Overhaul Kit
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Cadillac Deville | DEVILLE, HIGH LUXURY, SEVILLE, SLS, STS, TOURING 4 DOOR, TOURING SEDAN | 8 Cyl 4.6L
View related parts
Cadillac Deville Caliper Kit,Rear Brake
Part Number: 18040086
Product Specifications
- Other Name: CALIPER KIT, Wheel Cylinder Piston; Caliper Overhaul Kit, Overhaul Kit
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2002 Cadillac Deville | DEVILLE | 8 Cyl 4.6L
View related parts
Cadillac Deville Caliper,Rear Brake
Part Number: 18048080
$190.69 MSRP: $343.58
You Save: $152.89 (45%)
Product Specifications
- Other Name: CALIPER, Wheel Brake Cylinder/Caliper; Caliper
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2003-2005 Cadillac Deville | DEVILLE | 8 Cyl 4.6L
View related parts
Cadillac Deville Caliper Asm,Rear Brake
Part Number: 88962835
Product Specifications
- Other Name: CALIPER, Wheel Brake Cylinder/Caliper; Caliper
- Position: Rear
- Replaces: 18040792
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1999 Cadillac Deville | SLS, STS | 8 Cyl 4.6L
View related parts
Cadillac Deville Caliper Asm,Rear Brake (Service)
Part Number: 18048079
$191.53 MSRP: $343.58
You Save: $152.05 (45%)
Product Specifications
- Other Name: CALIPER, Wheel Brake Cylinder/Caliper; Caliper
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2003-2005 Cadillac Deville | DEVILLE | 8 Cyl 4.6L
View related parts
Cadillac Deville CALIPER
Part Number: 88962836
Product Specifications
- Other Name: CALIPER, Wheel Brake Cylinder/Caliper
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1999 Cadillac Deville | SLS, STS | 8 Cyl 4.6L
View related parts
Cadillac Deville Caliper Kit,Front Brake
Part Number: 18017156
Product Specifications
- Other Name: CALIPER KIT; Caliper Overhaul Kit, Overhaul Kit
- Position: Front
- Replaces: 18024958
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-2005 Cadillac Deville | 2 DOOR, 4 DOOR, 60 SPECIAL 4 DOOR, CONVERSION, DEVILLE, FUNERAL COACH, HIGH LUXURY, LIMOUSINE, SEVILLE, SLS, STS, TOURING 4 DOOR, TOURING SEDAN | 8 Cyl 4.6L, 8 Cyl 4.9L
View related parts
Cadillac Deville Caliper Kit,Rear Brake Repair
Part Number: 18029823
Product Specifications
- Other Name: CALIPER KIT, Wheel Brake Cylinder/Caliper; Caliper Overhaul Kit, Overhaul Kit
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1999 Cadillac Deville | 4 DOOR, DEVILLE, SLS, STS | 8 Cyl 4.6L, 8 Cyl 4.9L
View related parts
Cadillac Deville Caliper,Front Brake
Part Number: 18014745
Product Specifications
- Other Name: CALIPER, Wheel Brake Cylinder/Caliper; Caliper
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-1999 Cadillac Deville | 4 DOOR, DEVILLE | 8 Cyl 4.6L
- 1991-1993 Cadillac Deville | 2 DOOR, 4 DOOR, 60 SPECIAL 4 DOOR, CONVERSION, TOURING 4 DOOR | 8 Cyl 4.9L
View related parts
Cadillac Deville Caliper Asm,Front Brake (Service)
Part Number: 18029937
Product Specifications
- Other Name: CALIPER, Wheel Brake Cylinder/Caliper; Caliper, Caliper Assembly
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1996 Cadillac Deville | 4 DOOR | 8 Cyl 4.6L, 8 Cyl 4.9L
View related parts
Cadillac Deville Caliper Asm,Front Brake (Service)
Part Number: 18029938
Product Specifications
- Other Name: CALIPER, Wheel Brake Cylinder/Caliper; Caliper, Caliper Assembly
- Position: Front
- Replaces: 18029929, 18021252
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1996 Cadillac Deville | 4 DOOR | 8 Cyl 4.6L, 8 Cyl 4.9L
View related parts
Cadillac Deville Caliper,Front Brake
Part Number: 18014744
Product Specifications
- Other Name: CALIPER, Wheel Brake Cylinder/Caliper; Caliper
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-1999 Cadillac Deville | 4 DOOR, DEVILLE | 8 Cyl 4.6L
- 1991-1993 Cadillac Deville | 2 DOOR, 4 DOOR, 60 SPECIAL 4 DOOR, CONVERSION, TOURING 4 DOOR | 8 Cyl 4.9L
View related parts
Cadillac Deville Caliper Asm,Rear Brake
Part Number: 89047664
Product Specifications
- Other Name: CALIPER, Wheel Brake Cylinder/Caliper; Caliper
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2002 Cadillac Deville | SEVILLE, SLS, STS | 8 Cyl 4.6L

| Page 1 of 2 |Next >

1-20 of 31 Results

Cadillac Deville Brake Calipers

The Brake Caliperss used in Cadillac DeVille plays a great role in the braking system to change hydraulic pressure from the master cylinder to mechanical force. It is the force that causes the brake pads to rub against the rotors and in the process slow down or stop the vehicle. Cadillac DeVille models utilize two primary types of Brake Calipers: based on the kind of value that is being translated the two important types, which are fixed and floating. In the case of fixed versions there are several pistons in front of or behind the rotor, while in the latter, floating calipers, there is only one piston on the front side that slides towards the rotor; however, they wear unevenly if not properly maintained. Cadillac DeVille brake calipers have developed over the years with OE calipers for regular use and performance Calipers affording more resilience and a touch of style and class. Available performance options include economical cast with the option of lightweight aluminum for different driving requirements. The Brake Caliper require constant inspection and maintenance to avert problems such as leaks or uneven wear or brake drag issues for the optimal performance and security.

Each OEM Cadillac Deville Brake Calipers we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

Cadillac Deville Brake Calipers Parts Questions & Experts Answers

Caliper Assembly, Front Brake
25846387
Q: How do you remove and install Brake Calipers?
A: To remove the front brakes, start by loosening the lug nuts on the front wheels, but don't remove them completely. Then, raise the front of your ride and secure it on jackstands. Remove the front wheels and wash the brake assembly with brake system cleaner. Disconnect the Brake Line from the caliper and plug it to avoid contaminants entering the brake system hence minimizing loss of brake fluid. Next, remove the caliper mounting bolts and detach the caliper from its mounting bracket. To install new brakes on your vehicle's front, reverse removal of all components taken out ensuring that you replace sealing washers placed either side of a new fitting of a break line as well. Tighten banjo bolt along with caliper mounting bolts as per torque specifications.Thereafter,you will need to bleed your automotive braking system,mounting back tires together with lug nuts then lower down your car .Fasten lug nuts in compliance with their set torque specification while at this juncture.lowering is performed after installing wheel lugs while tightening them up properly.If you are considering rear brakes, follow a similar process.Firstly,don't forget to loosen up lug nuts on back wheels,later raise down rear side of your automobile which is then secured using jack stands.Remove rear wheels without forgetting to disengage parking brakes.dissemble brake lever by disconnecting parking cable then release it from bracket provided inside calliper.Unscrew banjo bolt then unplug fitting located at end point in order to prevent leakage because this may lead to contamination.Finally,take away caliper's mounting bolt sliding it off upper guide pin.To install new brakes you should adhere to an installation process that is opposite to removing so that sealing washer for threaded junction between line and clamp is tightened.Banjo bolt as well as caliper functional components must be fastened firmly when compared to other parts such as those in pistons.Carry out bleeding process across entire system where afterward wheels are installed on rims and lug nuts fastened before vehicle is allowed to descend as you tighten its lugs accordingly.The above procedures must be replicated while attending to the rear brakes.