What are the recommendations for replacing a muffler,Tail Pipe and connecting exhaust system parts on Buick Regal?

These units are typically connected by flanges at the rear of the converter and at either end of mufflers either by an original weld or by U-clamps working over a pipe connection in which one side of the connection is slightly larger than the other. You may have to cut the original connection and use the pipe expander to allow the original equipment exhaust pipe to be fitted over the new muffler. In this case, you'll have to purchase new U-clamps to fasten the joints. GM recommends that whenever you replace a muffler, all parts to the rear of the muffler in the exhaust system must be replaced. Also, all slip joints rearward of the converter should be coated with sealer before they are assembled. Be careful to connect all U-clamps or other hanger arrangements so the exhaust system will not flex. Assemble all parts loosely and rotate parts inside one another or clamps on the pipes to ensure proper routing of all exhaust system parts to avoid excessive heating of the floorpan, fuel lines and tank, etc. Also, make sure there is clearance to prevent the system from rattling against spring shackles, the differential, etc. You may be able to bend long pipes slightly by hand to help get enough clearance, if necessary. While disassembling the system, keep your eye open for any leaks or for excessively close clearance to any brake system parts. Inspect the brake system for any sort of heat damage and repair as necessary.

Genuine Buick Regal Tail Pipe

Exhaust Tail Pipe

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

6 Tail Pipes found

View related parts
Buick Regal Sleeve Assembly, Exh Tail Pipe Ht
Part Number: 13487425
$248.44 MSRP: $373.04
You Save: $124.60 (34%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Exhaust Heat Shield
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2018-2020 Buick Regal | 1SX 4 DOOR HATCHBACK | 4 Cyl 2.0L, 6 Cyl 3.6L
View related parts
Buick Regal Sleeve Assembly, Exh Tail Pipe Ht
Part Number: 13487424
$229.34 MSRP: $344.34
You Save: $115.00 (34%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Exhaust Heat Shield
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2018-2020 Buick Regal | 1SX 4 DOOR HATCHBACK | 4 Cyl 2.0L, 6 Cyl 3.6L
View related parts
Buick Regal Exhaust Muffler Assembly (W/ Tail Pipe)
Part Number: 25515884
Product Specifications
- Other Name: Muffler Asm,Exhaust (W/ Tail Pipe); Muffler
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1987 Buick Regal | 2 DOOR, 4 DOOR, REGAL | 6 Cyl 3.8L
View related parts
Buick Regal Muffler & Tail Pipe Assembly
Part Number: 14063933
Product Specifications
- Other Name: Muff & Tail Pipe Asm; Muffler, Muffler & Pipe
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1983 Buick Regal | 2 DOOR, 4 DOOR, STATION WAGON | 6 Cyl 3.8L, 6 Cyl 4.1L, 6 Cyl 4.3L Diesel, 8 Cyl 5.7L Diesel
View related parts
Buick Regal Muffler & Tailpipe Assembly
Part Number: 22505920
Product Specifications
- Other Name: Muffler & Tailpipe Asm; Muffler
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1987 Buick Regal | REGAL | 8 Cyl 5.0L
View related parts
Buick Regal Exhaust Crossover Pipe Assembly
Part Number: 22504709
Product Specifications
- Other Name: Pipe Assembly, Exhaust Crossover; Cross Over Pipe, Pipe
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1987 Buick Regal | REGAL | 8 Cyl 5.0L

Buick Regal Tail Pipe

The Tail Pipe of Buick Regal vehicles serves a significant part of the exhaust system by funnelling the exhaust gases from the manifold and then to the rear of the vehicle where it shall be released to the atmosphere. There have been many designs of Tail Pipes that have been produced over the years and some automobiles have used several pipes that create harmony. As for the final length of the Tail Pipe, it is possible to have it Straight Cut, Angled Cut and it can be accented with chrome tips for a sporty and stylish look. One used to find exhaust outlets neatly installed between the two packages of the rear bumper and this was common in the luxury cars up until it was discontinued because maintaining it used a lot of money. In general, Tail Pipe designs depend on the functionality parameters, demand, and the appearance.

Each OEM Buick Regal Tail Pipe we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

Buick Regal Tail Pipe Parts Questions & Experts Answers

Muffler & Tailpipe Assembly
22505920
Q: What are the recommendations for replacing a muffler,Tail Pipe and connecting exhaust system parts on Buick Regal?
A: These units are typically connected by flanges at the rear of the converter and at either end of mufflers either by an original weld or by U-clamps working over a pipe connection in which one side of the connection is slightly larger than the other. You may have to cut the original connection and use the pipe expander to allow the original equipment exhaust pipe to be fitted over the new muffler. In this case, you'll have to purchase new U-clamps to fasten the joints. GM recommends that whenever you replace a muffler, all parts to the rear of the muffler in the exhaust system must be replaced. Also, all slip joints rearward of the converter should be coated with sealer before they are assembled. Be careful to connect all U-clamps or other hanger arrangements so the exhaust system will not flex. Assemble all parts loosely and rotate parts inside one another or clamps on the pipes to ensure proper routing of all exhaust system parts to avoid excessive heating of the floorpan, fuel lines and tank, etc. Also, make sure there is clearance to prevent the system from rattling against spring shackles, the differential, etc. You may be able to bend long pipes slightly by hand to help get enough clearance, if necessary. While disassembling the system, keep your eye open for any leaks or for excessively close clearance to any brake system parts. Inspect the brake system for any sort of heat damage and repair as necessary.